GamePP Frequently Asked Questions

The parkour in this game looks amazing in 4K, but the sudden FPS drops are absolutely infuriating. The VRM heatsink on the ASRock B450M-HDV R4.0 just can't handle high-TDP CPUs, with temps spiking to 95-105℃ after an hour, triggering aggressive thermal throttling. I tried enabling 'Extreme Performance' in the BIOS, but the temps hit 110℃ and the whole system just rebooted—talk about a wake-up call. I ended up rigging a small 40mm fan to blow directly onto the VRMs and set a -0.05V undervolt curve in the BIOS. In my side-by-side tests, the core clock stayed locked at 4.2GHz without any dips. I previously tried lowering the CPU multiplier to save temps, but the FPS dropped to 40, which was totally unplayable. VRM temps now sit at 68-75℃. I switched the power mode to Balanced, and the fan stays around 1400-1600RPM. Last updated on2026-04-11 16:57:34。

Every time I entered a busy Tokyo district, the game would just vanish and dump me back to the desktop, which is incredibly stressful during key plot moments. The default XMP profile on the Colorful B760M-D PRO V20 has some compatibility quirks with certain memory dies, causing the memory controller voltage to dip to around 1.1V under load. I tried flashing the latest BIOS, but the crashes didn't stop and I even started getting weird BSOD codes—it was a total nightmare. I eventually ditched XMP and manually loosened the primary timings from 36-36-36-76 to 38-38-38-80, while locking the SOC voltage at 1.25V. MemTest86 errors dropped from 12 to zero. I tried pushing for 34-34-34-72, but the system just refused to boot. Memory temps stayed between 45-52℃. The system is finally stable, though I hate that I had to sacrifice a bit of clock speed. Last updated on2026-03-15 11:53:18。

My blocks were lagging by about 80ms on screen, and that mushy feeling is a total disaster when you're facing high-difficulty bosses. It turns out some of the USB 3.1 ports on the MSI B450M MORTAR MAX were fighting for IRQ resources during high-frequency input, causing latency spikes between 15ms and 45ms. I tried swapping out my peripherals for different brands, but the lag followed me, making me realize this was a motherboard-level issue. I went into the BIOS, forced the USB mode to Gen2 instead of Auto, and disabled USB selective suspend in Device Manager. Using a latency tester, my response time plummeted from 32ms to a crisp 8-12ms. I had a brief moment of panic when my mouse disconnected after the first tweak, but updating the chipset drivers sorted it out. Southbridge temps sat around 48-54℃. After three brutal boss fights, the input is finally responsive and feels instant. Last updated on2026-03-12 09:03:24。

This was a joke. In a game with such detailed environments, my PC felt like a dinosaur that decided to quit every time a large model loaded. The Intel 760P's controller voltage was jumping between 0.9V and 1.1V, causing severe checksum errors during sector reads, which triggered the BSOD. I tried lowering the texture resolution, but while the FPS went up, the crashes stayed exactly the same—a complete waste of time. I used the Intel Memory and Storage Tool to flash the latest stable firmware and set the disk power state to 'Always On' in the Windows power options. During a Prime95 stress test, the drive stopped throwing I/O errors and ran for four hours without a single crash. I did have a moment where the software froze and the drive disappeared from the system, but a quick M.2 reseat fixed it. Temps are 45-52℃. I've backed up the power profile now, but honestly, it's time to upgrade this old drive. Last updated on2026-04-19 16:13:30。

Whenever I unleash massive magic attacks, my frame rate tanks from 110 FPS down to 55 FPS, and the judder is just jarring. After digging into the telemetry, I found that with PBO enabled, the core voltage on the ASUS ROG STRIX X870-A was dipping violently between 1.12V and 1.18V under transient loads, forcing the CPU to downclock. I wasted some time switching the Windows power plan to Ultimate Performance, but the stutters persisted, which was honestly frustrating. I eventually dove into the BIOS, manually set the Load-Line Calibration to L3 mode, and added a +0.02V voltage offset. Monitoring with HWiNFO showed the core voltage finally stabilizing between 1.25V and 1.28V. I did hit a snag where the system hung at the splash screen during the first boot, but adding a tiny 0.01V bump to the DRAM voltage fixed it. VRM temps stayed chill at 52-58℃. After a full stress test, the stuttering is gone, though the BIOS menu is still a bit clunky to navigate. Last updated on2026-03-11 19:49:31。