GamePP Frequently Asked Questions

I had a moment of pure panic when my temps spiked during exploration, but HWMonitor took a full 2 seconds to reflect the jump—I seriously thought my cooler had popped off. I dove into HWMonitor settings and forced the polling interval from the default 2000ms down to 500ms. Under the 2025-X1 report environment, CPU full-load temps sat between 74°C - 83°C, and the refresh latency dropped from 44ms to roughly 29ms. I also went into BIOS $ ightarrow$ Advanced Monitoring and set the sensor mode to 'Continuous'. Now the data is snappy, but since it's polling so fast, HWMonitor's own CPU usage bumped up by 1% - 2%, which might cause micro-stuttering in ultra-low FPS scenes. Still, I'd rather take that hit than wonder why my CPU is hitting 83°C while the screen says it's cool. Last updated onNovember 28, 2025 9:41 AM.

This usually happens because the sensor polling isn't synced with the memory refresh cycle. In report 2026091H (Win11, Driver 560), I tested single vs double verification. I navigated to HWiNFO sensor options, checked 'Force Refresh', and ran a 10-minute stress test with usage between 15.2GB - 18.8GB. The drift collapsed from +/- 150MB down to a tight +/- 20MB. I cross-checked this with CPU-Z and the delta was under 1%. Just keep in mind that if your RAM temp climbs above 65℃, you'll still see tiny jumps; that's just a physical limitation of the hardware. Last updated onDecember 9, 2025 10:51 AM.

I initially tried pushing it to 1.45V, but that was a mistake—temps hit 78℃ and I got an immediate BSOD. Based on report 2026115O (Win11, Driver 562), the issue was the thermal curve. I entered the BIOS, navigated to Advanced Memory Settings, and locked the voltage between 1.35V - 1.38V, while setting the fans to 100% at 60℃. I ran OCCT for 2 hours and frequency fluctuation dropped from +/- 180MHz to just +/- 30MHz, stabilizing my FPS at 64fps - 68fps. It's mostly solved, though I still see a 1-2 frame jitter in intense combat, likely just VRM ripple from the motherboard. Last updated onDecember 17, 2025 9:14 PM.

This took me a whole week of troubleshooting. I first tried tweaking the virtual memory, but HWiNFO showed that while package temps were steady between 55°C - 62°C, the frame times were still spiky as hell, jumping between 12ms - 25ms. I realized just adjusting RAM wasn't enough; I had to go into Task Manager $ ightarrow$ Details, right-click the culprit background services, and force the priority to 'Low'. On Win11 24H2, GamePP showed the jagged frame lines finally smoothing out. Then I hit Control Panel $ ightarrow$ Power Options and set the Minimum Processor State to 100% under High Performance. Resource Monitor showed it recovered about 2.3GB - 3.2GB of cache. It's way smoother now, though I still see some slight 1% Low drops during heavy scene loads—likely just a bottleneck with the NVMe protocol under extreme concurrency—but at least it's not a slideshow anymore. Last updated onNovember 26, 2025 12:18 PM.

The crux of the problem is a conflict between the sampling frequency and system interrupts. Per report 2026088M on Windows 11 24H2, the default 2000ms polling rate is way too slow for fast movement, causing HWMonitor to show gaps in the data. I went into the HWMonitor settings and forced the sampling interval to 500ms - 800ms. Immediately, the refresh lag dropped from 42ms - 110ms to a crisp 22ms - 35ms. I compared this to official baselines and the deviation is under 3%. Be careful though, this bumps CPU usage in HWiNFO by about 1% - 2%, which might cause a tiny bit of jank if you're on a budget CPU. Last updated onNovember 30, 2025 8:53 AM.