Having the game crash randomly every single time I launch it is an absolute nightmare; I almost threw my keyboard across the room. The Gloway Celestial DDR5 6000MHz 32GB sticks were experiencing violent voltage swings between 1.1V and 1.35V during the initial asset load, which just made the memory controller give up. I tried updating the motherboard BIOS to the latest version first, but that actually broke my XMP profile and didn't fix the crashes—it was a total disaster. I went into the advanced voltage settings in BIOS, locked both VDD and VDDQ at 1.4V, and loosened the tRFC timing from 480 to 520. In OCCT memory stress tests, the errors dropped from 15 per hour to zero, and the boot success rate hit 100%. I actually pushed the voltage to 1.5V at one point, which sent the RAM temps skyrocketing to 65℃, so I backed it off to 1.4V for safety. RAM temps now sit at 52-58℃ and VRMs are at 60-66℃. Used the BIOS export tool to save the voltage profile as a backup. Last updated onApril 1, 2026 6:47 PM.
Honestly, the power delivery on this Onda A520-VH-W is a joke; it's like walking a tightrope under load. After about two hours of gaming, the Vcore would tank from 1.2V to 1.05V, which just killed the game process and sent me straight back to the desktop. I tried enabling auto-overclocking in the BIOS, but the VRMs overloaded instantly and the whole PC just shut down—absolutely ridiculous. I decided to play it safe and went into Windows Power Management, capping the Maximum Processor State at 99% to kill Turbo Boost and lower the heat. In AIDA64 FPU tests, the voltage ripple shrank from 0.15V to 0.03V, and the game stopped crashing. I did lose about 5 FPS, but that's a tiny price to pay for not crashing every hour. VRM temps are now stable at 78-84℃ with fans screaming at 2200 RPM. I've backed up these power settings so I don't have to deal with this nightmare again. Frame times are now 12.4-15.1ms. Last updated onMarch 29, 2026 8:56 AM.
Every time I loaded into the ancient ruins, the game would just crash to desktop without warning—it was honestly ridiculous. The Intel 760P is an older NVMe, and when handling the high throughput of modern games, the lack of efficient garbage collection caused read/write latency to spike over 150ms. I tried reinstalling the game, but it crashed at the exact same spot, which was a total waste of my time and left me feeling pretty defeated. I eventually manually triggered a system-wide TRIM command and used a disk tool to keep at least 30% of the space free to reduce write amplification. CrystalDiskInfo shows health at 82-85%, and speed fluctuations narrowed to 1500-1800MB/s. The system felt sluggish for a moment right after the TRIM, but a reboot and cache clear fixed it. Temps are 38-44℃, and the load is evenly distributed. After exporting the optimization config, temps stayed at 38-44℃. Last updated onApril 6, 2026 8:52 PM.
The scheduling logic on this RAM is just pathetic. Every time I loaded a map, the frequency would bounce wildly between 6000MHz and 4800MHz, leaving the progress bar stuck at 99% forever. The voltage on the Gloway Celestial Yi DDR5 6000MHz 16GB was swinging by 0.1V during low-load transitions, causing the memory controller to reset constantly and dragging load times from 10 seconds to 35 seconds. I tried updating the motherboard drivers first, but that just slowed down my boot time by a second and did nothing for the loading—I was honestly about to lose it. I went into the BIOS, switched the RAM voltage from Auto to a locked 1.35V, and disabled all power-saving modes. CPU-Z now shows the frequency dead-locked at 6000MHz with zero jumping, and the loading speed is back to normal. My first attempt at locking the voltage sent temps spiking to 62℃, so I had to slap on some small heatsinks to bring it down to 52-56℃. Latency is now steady at 75-80ns with 52GB/s bandwidth. Saved the profile to a BIOS backup, and it's been rock solid since. Last updated onApril 12, 2026 5:47 PM.
By the time I hit the late game, the frame rate started bleeding out slowly—the optimization is honestly a joke. The RT620P is a massive cooler, but in a closed-off case, it suffers from terrible heat soak over long sessions, leaving the core hovering between 82℃ - 88℃ and forcing the CPU to downclock. I tried capping the max frame rate, but that just added a weird feeling of input lag, which was a frustratingly rookie mistake. I ended up redesigning the whole case airflow, setting the front fans to aggressive intake and the rear to high exhaust, while switching the RT620P to an aggressive fan curve. Under a CrystalDiskMark stress load, the core temp dropped from 85℃ to 72℃ - 76℃, and the lag finally eased up. I did notice some air leaking from the top of the case after the change, but adding a dust filter and sealing the gaps fixed it. The CPU now stays between 65℃ - 72℃. I used a system snapshot tool to back up all these thermal settings, and the core is holding at 65℃ - 72℃. Last updated onApril 9, 2026 11:17 AM.
