Question 1

Marvel Rivals is dropping frames due to thread scheduling issues with my CR-1400. BIOS priority fix?

Accepted Answer

This was honestly ridiculous—my frames were dropping from 180 to 80 in basic combat. It made zero sense. After comparing logs, I found that on my Jonsbo CR-1400 build, the default scheduler was dumping heavy tasks onto the E-cores while the P-cores were just chilling. I tried disabling the E-cores entirely, but that just made the whole system feel sluggish and caused some apps to crash—definitely too extreme. I went into the BIOS advanced menu, manually set the scheduling priority to 'Performance First', and locked the minimum processor state to 100% in the Windows Power Plan. The frame time graph, which used to look like a mountain range, finally flattened out to a steady 4-7ms. I did see a 12W increase in idle power draw, but I sorted that out by reconfiguring the E-core sleep states. CPU temps are now 62-68℃ and the system is rock steady. Backed up the profile, and VRM temps are holding at 60-66℃.

Question 2

Zenless Zone Zero keeps crashing after long battles on my ASUS B760M TUF, this is so frustrating!

Accepted Answer

It's honestly ridiculous—every time I'd trigger a big skill in a boss fight, the game would just crash, which is a total disaster for the experience. The memory compatibility on my ASUS B760M-PLUS D4 was struggling with the 3200 MHz XMP profile, hitting constant address conflicts at 16-18-18-36 timings. I wasted two hours reinstalling the game thinking it was a corrupted file, which was just a massive waste of time and left me feeling pretty annoyed. I eventually went into the BIOS, ditched the aggressive XMP, and manually loosened the timings to 18-22-22-42 while nudging the frequency down to 2933 MHz. In MemTest86, the 6 errors per hour vanished completely, and the system became rock solid. I did notice a tiny drop of about 3 FPS in my minimums after loosening the timings, but I got that performance back by bumping the RAM voltage to 1.32V. RAM temps are now between 38 - 44℃ and the motherboard core is at 45 - 52℃. I used a system snapshot tool to save this config, and fans are steady at 1400 - 1600 RPM.

Question 3

I'm getting bad frame drops while walking through cities in Metaphor: ReFantazio on my i5-14600KF. Can I fix this with priorities?

Accepted Answer

This is just ridiculous—my frame rate would drop from 140 to 60 in a simple walking scene. It totally defied logic. I found that the default scheduling was dumping heavy tasks onto the E-cores while the P-cores were just sitting there idling. I tried disabling the E-cores entirely, but that was a mistake—the whole system became sluggish and some apps started crashing, so I backed off immediately. Instead, I went into the deep BIOS menus and manually set the core scheduling priority to Performance, then locked the minimum processor state to 100% in the Windows power plan. Looking at the frame time graphs, the wild spikes finally flattened out, and my frame times stabilized at 6-10ms. My idle power draw jumped by about 10W at first, but I managed to mitigate that by tweaking the E-core sleep states. The CPU now runs at 60-66℃, and the input response is finally snappy and precise.

Question 4

I'm getting huge frame drops in Elden Ring DLC during fights. Is the Huntkey T600 ripple the problem?

Accepted Answer

This was a total nightmare. Right as I hit the final boss, my frames plummeted from 60 to 20 without warning. I found that under full load, the 12V rail on the Huntkey T600 Colorful was hitting 82mV of ripple, causing the GPU voltage to jitter and trigger a hardware-level downclock. I tried capping the frame rate in the driver, but that just added input lag, which made me absolutely furious. I eventually swapped the single 8-pin daisy-chain for two independent power cables and redistributed the peripheral load. Using an oscilloscope, I saw the ripple peak drop from 82mV to a clean 35-42mV, and frame times stabilized from 8-30ms to a tight 6-10ms. I had one scare where the PC rebooted due to a loose modular connector, but once I seated it firmly, it was perfect. PSU internal temps are now 45-52°C. I saved the config snapshot, and the game finally feels responsive again.

Question 5

I'm seeing massive frame drops during city transitions in FF7 Rebirth with my WD SN850X 1TB, help!

Accepted Answer

This is just ridiculous—my frames were dropping from 120 to 40 during simple scene transitions. It made no sense. I found that the default WD SN850X 1TB drivers were struggling with random small-file reads, leading to a massive I/O queue buildup that left the CPU idling. I tried killing all background sync apps, but the drops stayed—a total waste of effort. I installed the WD Dashboard, enabled 'Game Mode', and optimized the driver cache, while setting the Windows power plan to 'Never Turn Off' for the hard disk. The frame time graph finally flattened out, with generation times stabilizing at 8-12ms. I did notice a 2W increase in idle power draw after enabling Game Mode, but I tweaked the energy thresholds to balance it out. Drive temps are sitting at 48-54℃. I've exported this I/O config as a backup just in case, but it's been rock solid so far.

Question 6

My CPU throttles during large city builds in Manor Lords with a PA120 SE, can I fix this with fan curves?

Accepted Answer

It was honestly ridiculous—during complex city simulations, my CPU temps spiked straight to 95 ℃, causing the clock speed to get sliced in half. The default fan curve on the Thermalright PA120 SE is way too conservative; it just couldn't react fast enough to the bursts, and my temps would jump from 60 ℃ to 90 ℃ in about two seconds. I tried using a power-saving mode, but the FPS dropped to 30, which was just a waste of time. I went into the BIOS and switched the PWM curve to an aggressive profile, forcing the fans to 1500 RPM as soon as the chip hits 70 ℃. HWInfo shows the peaks are now held between 78 - 84 ℃, with frequencies stable at 4.2 GHz. The fans sounded like a jet engine at first, but I dialed back the sub-50 ℃ speed to 800 RPM to keep my sanity. Heatsink temps are around 35 - 40 ℃. I saved this profile as a snapshot, and now the fans stay steady at 1500 - 1800 RPM.

Question 7

Is optimizing BIOS frequency the answer to memory allocation drops in Palworld on Crucial DDR4 3200?

Accepted Answer

It's honestly ridiculous—just walking around my base, my FPS would tank from 80 to 30 for no apparent reason. It felt like the game was fighting my hardware. I found that the default XMP profile for the Crucial DDR4 3200 was hitting frequent refresh delays when handling massive amounts of entity data, making the CPU wait on the RAM. I tried killing every background app in Task Manager, but the drops stayed, so I gave up on that. I went into the BIOS and hard-locked the frequency at 3200MHz and set the minimum processor state to 100% in Windows. The frame time graph, which used to look like a mountain range, finally flattened out to a steady 12-16ms. The RAM temp climbed by 4℃ initially, but I tweaked the exhaust fan curve to bring it back down to 45-51℃. I used a system snapshot tool to back up the config, and it's finally rock solid.

Question 8

The First Descendant keeps crashing with storage verification errors on my FireCuda 530 after long sessions. Help?

Accepted Answer

This was beyond frustrating—the game would crash exactly when a high-tier item dropped. It's a complete disaster for the experience. The Seagate FireCuda 530 was hitting verification conflicts while handling fragmented save files under PCIe 4.0 load, leading to storage address errors. I wasted three hours reinstalling the game, which did absolutely nothing and just made me more angry. I eventually went into Device Manager and disabled the write caching policy and updated the firmware. In CrystalDiskMark stress tests, the crashes went from 3 per hour to zero. I noticed that disabling the cache added about 2 seconds to save times, but I fixed the overall snappiness by moving the page file to a different partition. Drive temps are now 42-50℃ and the motherboard is at 45-52℃. I used a system snapshot to back up this config so I don't have to do this again. The input response now feels tight and immediate.

Question 9

My Galax B760M D4 Wi-Fi Black Knight has scheduling issues in Dota 2 team fights; do I need to adjust virtual memory?

Accepted Answer

It was honestly ridiculous—my FPS would drop from 200 to 90 during simple laning phases. It made no sense until I realized the Galax B760M D4 Wi-Fi Black Knight was pushing heavy calculations to the E-cores while the P-cores were just chilling. I tried disabling the E-cores entirely in Windows, but that just made the whole system sluggish and caused some apps to crash, which was a total fail. I went back into the BIOS deep menu, set the core scheduling priority to 'Performance First', and locked the minimum processor state to 100% in the power plan. The frame time graph, which used to look like a mountain range, finally flattened out to a steady 3-6ms. Idle power draw increased by about 18W, but I managed to mitigate that by tweaking the E-core sleep states. CPU temps are now 58-64℃. I backed up the profile using the board tool, and it's finally stable.

Question 10

Monster Hunter Wilds keeps crashing after long hunts with Corsair Vengeance DDR4 3200. How to fix this?

Accepted Answer

It was honestly infuriating. I'd be right at the moment of capture and the game would just vanish. A total disaster. The Corsair Vengeance DDR4 3200 was hitting address conflicts at 16-18-18-36 under XMP, leading to memory parity failures. I wasted two hours reinstalling the game, which did absolutely nothing—just a huge waste of time. I finally went into the BIOS, ditched the aggressive XMP profile, and manually loosened the timings to 18-22-22-42, while dropping the frequency slightly to 2933MHz. MemTest86 went from 6 errors per hour to zero. I noticed a slight dip of about 5 FPS after loosening the timings, so I bumped the voltage to 1.32V to claw back some performance. RAM temps stayed between 40-46℃ and the motherboard core was at 48-54℃. I used a system snapshot tool to save this config so I never have to deal with this again. Temps are holding at 40-46℃.

GamePP Frequently Asked Questions

After overclocking the graphics card ZOTAC GeForce RTX 4080 SUPER Apocalypse OC 16G in the game Monster Hunter: Rise, power consumption is too high, how to set up AI performance testing in GamePP for monitoring?

How to overclock GPU VASTARMOR Radeon RX 9070 XT Super Alloy PRO via AI performance test in GamePP to optimize PUBG: BATTLEGROUNDS?

In Black Myth: Wukong, frame rates are low; I want to overclock my ZOTAC GeForce RTX 5080 AMP Extreme GPU. How to set fan speed in GamePP?

"How to Restore Default Settings in GamePP If Stuttering Occurs After Overclocking AMD Ryzen 9 9950X with RX 7900 XTX?"

How to use the overclocking settings function in GamePP to set core frequency for graphics card VASTARMOR Radeon RX 9070 GRE Starry Sky and track power temperature?