Question 1

I'm getting frame drops during LoL teamfights because my Hyper 612 APEX isn't reacting fast enough. Should I tweak the PWM curve?

Accepted Answer

There's nothing like the rush of a 5v5 teamfight when your CPU is firing on all cylinders. But weirdly, even at 1080p, I was getting these micro-stutters that were super obvious on my 240Hz screen. The default fan curve on the Cooler Master Hyper 612 APEX is way too conservative, letting the CPU spike to 88-94℃ before the fans really kick in, which triggers the motherboard's thermal throttle. I tried 'Maximum Performance' in the OS, but the stutters stayed—that's when I realized this was a physical cooling issue. I went into the BIOS, navigated to Hardware Monitor, cut the fan response delay from 2 seconds down to 0.5 seconds, and set the 100% speed threshold to 60℃. In AIDA64 stress tests, the peak temp dropped from 92℃ to a steady 72-76℃, and the FPS fluctuations vanished. At first, the fans sounded like a jet engine, but after smoothing out the 65-75℃ step curve, it's tolerable. CPU now stays at 68-72℃ and feels buttery smooth.

Question 2

I'm seeing frame drops during intense firefights in CS2 with my Jonsbo CR-1400 ARGB. Do I need to adjust the voltage offset?

Accepted Answer

In the middle of a smoke-filled firefight, I noticed the frames were jumping around, which is a death sentence in a competitive shooter. The Jonsbo CR-1400 ARGB White Edition just doesn't have the thermal mass to handle aggressive boosting, causing the CPU to bounce between 85-92℃ and triggering frequency shifts. I tried disabling Core Boost in the OS, but while temps dropped to 70℃, my 1% lows tanked from 140 to 110 FPS, which made me very nervous about losing performance. I went into the BIOS, navigated to Advanced Voltage Settings, set a voltage offset of -0.05V, and tweaked the fan curve to hit 80% speed at 65℃. HWMonitor shows the temps are now stable at 74-79℃, and the frame time variance shrunk from 5-12ms down to 3-6ms. I tried -0.08V, but the system BSOD'd the moment I launched the game, so I backed it off to -0.05V. CPU now sits at 76-81℃ with fans at 1500 RPM. The stuttering is gone, and the stability is finally verified.

Question 3

My Noctua NH-D15 G2 can't seem to handle the power spikes in Apex Legends, causing lag. What should I do?

Accepted Answer

It was a total nightmare—using a top-tier air cooler and still hitting thermal walls. This game pushes the CPU way harder than expected, and my FPS was diving from 160 to 90. Even with the massive NH-D15 G2, uneven thermal paste application caused a few cores to hit 94℃, triggering the motherboard's safety throttle. I tried the 'High Performance' power plan, but that just made it overheat faster, which was honestly pathetic. I ended up remounting the cooler entirely and navigated to the BIOS, then AMD Overclocking, where I set a PBO negative offset of 20. AIDA64 now shows the peak temps are capped at 78-83℃, with clocks staying locked around 4.8GHz. I tried pushing the offset to 30, but the system just rebooted during the loading screen, so I dialed it back. Fans are steady at 1200 RPM, and it's whisper quiet. I exported the temp curves from the stress test to backup the config, and it's finally stable.

Question 4

My ASRock B450M-HDV R4.0 is overheating during intense Nioh fights, causing massive lag. How do I fix this?

Accepted Answer

The combat went from fluid to a literal slideshow, which is a nightmare when you're fighting high-difficulty bosses. Checking the logs, the VRM area on the ASRock B450M-HDV R4.0 was hitting 105-110℃ under load, forcing the CPU clock to tank from 3.6GHz down to a pathetic 0.8GHz. I tried the 'High Performance' power plan first, but that just pumped more heat into the VRMs and triggered the throttling even faster—total fail. I ended up gluing three small aluminum heatsinks directly onto the chokes and navigated to the BIOS, then OC Tweaker, where I capped the CPU TDP at 65W to stop it from boosting too aggressively. According to HWInfo, VRM temps dropped to a manageable 82-88℃, and the clock finally stabilized around 3.2GHz. I actually knocked a capacitor loose while installing the heatsinks, causing a boot failure, but it's fine now after a quick fix. CPU temps are hovering at 72-78℃ with fans at 2200 RPM. Stress tests confirm the clocks aren't jumping anymore; the thermal bug is finally dead.

Question 5

I'm getting huge frame drops when entering buildings in RE Village on my Biostar A320MH PRO. Should I tweak virtual memory?

Accepted Answer

Every time I turned around in those creepy village hallways, there was this 0.3-second freeze that totally killed the immersion. The default memory timings on the Biostar A320MH PRO are way too loose, leaving latency swinging between 95-110ns, which just chokes the game engine's resource scheduling. I wasted time messing with the page file, but that did absolutely nothing for the hardware latency, which left me feeling pretty anxious. I went into the BIOS, navigated to Memory Configuration, manually pushed the primary timings from 18-22-22 down to 16-18-18, and bumped the DRAM voltage to 1.35V. AIDA64 showed the latency drop from 102ns to a tight 78-82ns, and the game suddenly felt snappy. I tried pushing for 14-16-16, but the system BSOD'd the second the game loaded; I had to loosen tRFC to 600 to get it stable. RAM temps are now 42-48℃ with the VRMs at 55-60℃. The input lag is gone, and the settings are locked in.

Question 6

My Onda H610M is having voltage drops in crowded Hitman 3 scenes, causing FPS to tank. Will locking the frequency help?

Accepted Answer

Man, running Hitman 3 on this board is like walking a tightrope. Whenever the crowd gets thick, my FPS plummets from 60 to 25, and the game looks like a PowerPoint presentation. The Onda H610M's power delivery just can't handle an i5 boosting all cores, with voltage swinging wildly between 1.1V and 1.25V, triggering protective throttling. I tried dropping every single graphics setting to low, but I only gained about 3 FPS—total waste of time and honestly kind of hilarious. I finally went into the BIOS, navigated to Advanced CPU Settings, locked the CPU core frequency at a steady 3.8GHz, and slapped two tiny heatsinks on the VRM chokes. HWInfo shows the Vcore is now stable around 1.2V without those nasty spikes. I tried locking it at 4.2GHz at first, but it froze on the loading screen; dropping it by 400MHz finally did the trick. CPU temps are 75-82℃ with fans at 2100 RPM. I exported the voltage curves from the logs to confirm the stability, and the data looks clean.

Question 7

My Colorful B760M-D PRO V20 VRMs are overheating in Tales of Arise, causing my CPU to throttle. Should I limit the TDP?

Accepted Answer

This was an absolute nightmare. The power delivery on this board is a joke for modern CPUs; my frame rate was dropping from 90 down to 30 in cycles. The Colorful B760M-D PRO V20 has zero heatsinks on the VRMs, and under load, they hit 110℃, forcing the CPU clock to tank from 4.4GHz to 0.8GHz. I tried the 'High Performance' power plan first, but that just made it run hotter and throttle faster—total facepalm moment. I ended up gluing three small aluminum heatsinks onto the chokes and capped the CPU TDP at 65W in the BIOS to stop the aggressive boosting. HWMonitor showed VRM temps drop from 110℃ to about 85-92℃, and the CPU finally stabilized around 3.6GHz. I actually messed up the installation and bumped a capacitor, which caused a boot failure, but I got it fixed. CPU temps are now 72-78℃ with fans at 2200 RPM. After backing up the BIOS, the fan speed is steady at 2100-2300 RPM.

Question 8

I'm getting these annoying frame drops while running through Kyoto in Like a Dragon: Ishin on a Maxsun B850M WIFI. Why?

Accepted Answer

While sprinting through the streets of Kyoto, I noticed these tiny 0.2-second hitches that are absolutely jarring on a 144Hz monitor. It turns out the Maxsun MS-Terminator B850M WIFI was defaulting the PCIe slot to Auto, which occasionally dipped back to Gen 3 speeds, causing the data throughput between the GPU and CPU to fluctuate around 15.8GB/s. I first tried enabling 'Prefer Maximum Performance' in the NVIDIA drivers, but that did absolutely nothing for the hardware link, which was honestly frustrating. I eventually dove into the BIOS, navigated to Advanced, then PCIe Configuration, forced the link speed to Gen 4, and disabled the Link State Power Management. After checking GPU-Z, the read/write bandwidth locked in at a steady 31.5GB/s, and those micro-stutters vanished. Interestingly, the system failed to boot twice after the first Gen 4 tweak; I had to reseat the GPU and clean the gold fingers before it stabilized. With the chipset temps sitting at 52-58℃, everything is rock steady now. I used the motherboard utility to export and save this I/O config.

Question 9

My Vastarmor RX 9070 XT Alloy hits the power wall in zombie-heavy areas in Dying Light 2, causing huge frame drops. Any fix?

Accepted Answer

Man, this card is a beast, but it runs like a space heater. My frame rate was plummeting from 110 down to 50 in a heartbeat. The Vastarmor Radeon RX 9070 XT Alloy hits a 250W power wall under extreme load, causing the clock to crash from 2.6GHz to 1.8GHz instantly. I tried maxing out every single graphics setting, and the PC just black-screened and rebooted—total fail, I actually laughed at my own stupidity. I went into the driver panel, capped the max power at 220W, and set a custom fan curve to hit 90% speed at 75℃. Monitoring with GPU-Z, the core clock finally stabilized around 2.3GHz without those violent dips. I actually tried capping it at 180W first, but the FPS drop was too severe and caused noticeable scene loading lag, so I bumped it back to 220W for the sweet spot. Temps are now between 72℃ and 78℃, and the fans are a bit loud. Exported the logs, and the fan speed is steady at 1400-1600 RPM.

Question 10

I'm getting frame drops in complex scenes in Judgment on my ASUS X870-A Snow. Do I need to force PCIe Gen 5 mode?

Accepted Answer

Walking through the neon streets of Tokyo with this setup is usually a dream, but I noticed something weird: whenever I turned quickly, the FPS would dip from 140 to 70. On a high-refresh monitor, that stutter is glaring. My ASUS X870-A Snow was defaulting the PCIe slot to Gen 4, capping the GPU bandwidth at 31.5GB/s. I tried the 'High Performance' driver setting, but the lag persisted, making me realize the issue was at the hardware link level. I dove into the BIOS, forced the PCIe link speed to Gen 5, and switched Windows to the 'Ultimate Performance' power plan. A GPU-Z bus interface test showed bandwidth jumping to 63GB/s, and the stutters vanished. Interestingly, the first time I toggled Gen 5, I got a brief black screen during boot; I had to update the GPU VBIOS to fully stabilize it. Board temps stay between 48℃ and 55℃. Frame times are now a rock-solid 4.2-5.8ms.

GamePP Frequently Asked Questions

After swapping RAM, game loading is slow, how to benchmark RAM performance for read/write speeds in Baldur's Gate 3 with GamePP?

During War Thunder gameplay, cooler temperature abnormally high, how to detect Thermalright Frost Commander 140 real-time temperature data using GamePP?

How to benchmark read/write speeds for Kingston FURY Beast 32GB DDR5 6000 memory in GamePP performance test

How to real-time monitor cooler Thermalright PA120 SE ARGB temperature in GamePP to prevent overheating in Elden Ring?

Overview: GamePP resolves game FPS drop issues Playing game League of Legends on graphics card ASUS ROG STRIX RTX 4070, FPS drops to 80 during team fights, so annoying!