Question 1

My Soyo SY-A320D4+ keeps crashing after two hours of Zenless Zone Zero, will voltage help?

Accepted Answer

I'm honestly done with this; it's low-frequency RAM, but it still crashes after two hours, which is ridiculous. The Soyo SY-A320D4+ has a pretty basic power delivery system, and I noticed the VDD voltage would randomly dip by 0.05V, triggering illegal memory access errors in the game. I tried updating the BIOS to the latest version, but that actually made the crashes happen more often—a complete disaster. I went into the BIOS voltage settings and locked VDD and VDDQ at 1.35V instead of the 'Auto' 1.2V. I ran Prime95 Large FFTs for 12 hours and didn't see a single error. The crashes are finally gone. I tried pushing it to 1.4V at first, but the RAM temp spiked to 65℃, so I backed it off to 1.35V for a better balance. Now it stays at 48-54℃ at 2666MHz. I exported the profile to a backup file so I don't have to do this again, and the game feels way more responsive.

Question 2

My Jginyue B760M D4 takes forever to load maps in Delta Force, do I need more RAM?

Accepted Answer

Getting into large battle maps was a nightmare; the loading screen would just hang at 99% for ten seconds. 8GB of RAM on a Jginyue B760M D4 is barely a survival kit for modern tactical shooters. My usage was constantly pegged at 92-97%, forcing the system to rely on the painfully slow page file. I tried clearing temp caches, but that only shaved off one second—totally pointless against a hardware bottleneck. I finally added another matching 8GB stick for a 16GB dual-channel setup. Resource Monitor showed usage drop to a comfortable 62-68%, and load times plummeted from 15 seconds to 6. I messed up the first install and it showed as single-channel, but moving the sticks to slots A2 and B2 fixed it. RAM is stable at 42-48℃ at 3200MHz. AIDA64 bandwidth tests showed read speeds jump from 32GB/s to 58-62GB/s, though RAM temps hit 58-63℃ under load.

Question 3

My Galax B760M D4 feels sluggish in the fog of Silent Hill 2, is my RAM running too slow?

Accepted Answer

I finally found the culprit! My RAM was stuck at the base 2133MHz frequency, which is basically a crime for this hardware. This bottleneck caused a 12-18ms instruction delay when the CPU handled occlusion culling, making the camera feel like it was moving through molasses. I tried the 'Ultimate Performance' power plan in Windows, but it only added 3 FPS—completely useless. I rebooted into the BIOS and loaded the XMP profile to hit 3200MHz. CPU-Z showed the jump immediately, and my minimums leaped from 42 FPS to 68 FPS. It was an instant adrenaline rush seeing it run so smoothly. I did have a scare where the PC wouldn't POST after enabling XMP, but a quick reseat of the sticks and cleaning the gold pins with an eraser fixed it. RAM is now 40-46℃ at 1.35V. In-game monitors show frame generation is perfectly flat at 5.1-6.4ms.

Question 4

I'm seeing random frame drops in Manor Lords when my city grows on an Onda 9D4-DVH, any tips?

Accepted Answer

It's honestly a joke that a slow-paced city builder can stutter this hard. The Onda 9D4-DVH's default RAM settings seemed okay, but during complex building calculations, my 0.1% lows would tank to 12 FPS. I tried to force it by bumping the voltage to 1.38V, but that was a disaster—the system blue-screened after 15 minutes. The frustration was real. I decided to take a step back and downclock the RAM to 2666MHz in the BIOS, tweaking the timings to 16-18-18-38. Using a frame time analyzer, I saw the minimums jump from 12 FPS to a much more playable 45 FPS. I actually thought it didn't work at first, but after three restarts and a half-hour session, it finally clicked. RAM temps are sitting at 48-54℃ with voltage stable at 1.35V. I ran four passes of MemTest86 and got zero bit-flip errors. Fan speeds are humming along at 1400-1600RPM, and the game is finally playable.

Question 5

My Biostar H310MHD3 keeps crashing in the open areas of Stalker 2, should I adjust the page file?

Accepted Answer

Every time I stepped into a dense forest area, the game would just vanish and dump me back to the desktop. It was stressful as hell. The Biostar H310MHD3 is a budget board, and with high settings, my RAM usage was pegged at 7.4-7.9GB, constantly hitting the system limit. I tried killing every single background app, but that only saved 300MB—hardly enough to stop the bleeding. I finally went into Advanced System Properties and switched virtual memory from 'Automatic' to 'Manual,' assigning a fixed 16GB to 32GB page file on my NVMe SSD. Resource Monitor showed the commit charge finally had some breathing room, and the crashes stopped entirely. I made a mistake and put the page file on a mechanical HDD first, which added a brutal 20-second delay to loads, so move it to your SSD. RAM temps are fine at 38-44℃, and disk load is around 12-25%. Event Viewer shows the memory access violations are gone, and the game feels much more responsive.

Question 6

My ASRock Z370M Pro4 keeps crashing during heavy scene loads in Hellblade 2, is it a power issue?

Accepted Answer

The framerate was bouncing between 60 and 30 FPS, which is a total nightmare for a cinematic game. After digging into the logs, I found the ASRock Z370M Pro4's VRMs were struggling with modern power spikes, causing a 0.08V drop that triggered a CPU safety shutdown. I tried lowering the graphics to medium, which added about 10 FPS, but the random crashes kept happening—it was incredibly frustrating. I eventually went into the BIOS, switched the CPU voltage to Manual, and added a +0.05V offset while disabling C-States to kill that wake-up lag. Monitoring via RTSS, the frame time graph went from a jagged mess to a nearly flat line between 16.5-18.2ms. I did hit a wall early on where the PC black-screened upon launching the game, but dialing the voltage back to 1.1V and cranking the fans fixed it. CPU temps now sit around 75-82℃ with VRMs at 68-74℃. OCCT ran for two hours without a single error, and RAM stayed at 58-63℃.

Question 7

I'm getting these weird frame drops in Space Marine 2 during huge fights on my B850M-K, any fix?

Accepted Answer

When facing waves of Tyranids, I noticed these jarring 18-20ms hitches that completely killed the flow. It turns out the default FCLK on the Maxsun B850M-K wasn't playing nice with the memory controller under heavy load, causing data throughput to swing wildly between 42-48GB/s. I wasted time messing with Windows Game Mode and clearing temp files, but that only gave me a pathetic 2 FPS boost—it was like trying to fix a leaky pipe with a band-aid. I finally dove into the BIOS Advanced settings and manually locked the FCLK at 2000MHz, then bumped the SoC voltage to 1.15V to keep it from crashing. Using AIDA64, I saw memory latency drop from a sloppy 82-90ns down to a tight 70-76ns. It wasn't a smooth ride though; the system rebooted twice during scene loads until I pushed the DRAM voltage from 1.2V to 1.35V. Now, with RAM idling at 44-50℃ and VRMs hitting 62-68℃, CPU-Z confirms everything is synced. Frame times are finally rock steady at 5.1-6.4ms.

Question 8

My game crashes after long sessions in Elden Ring: Shadow of the Erdtree on a Colorful B760M. Is it a power issue?

Accepted Answer

Absolutely unbearable. A mid-range board shouldn't just crash after two hours of gaming. The VRMs on the Colorful B760M FROZEN can't handle the transient spikes of an i7+, causing VCORE to drop by about 0.06V, which triggers an illegal memory access error in the game. I tried updating the BIOS, but that actually made the crashes more frequent—total disaster. I went into the BIOS voltage settings, switched VCORE from Auto to Manual, and added a +0.03V offset, while locking RAM voltage at 1.35V. OCCT stress tests ran for 12 hours with zero errors. The crashes are gone. The VRMs hit 88℃ at first, so I had to strap a tiny 40mm fan over the heatsinks to bring it down to 72 - 76℃. CPU stays between 68 - 75℃. Saved the profile to a USB drive for backup. Stability achieved.

Question 9

Turn transitions in Civ 7 are taking forever on my MSI Z890 EDGE. Is my XMP frequency causing the slow loads?

Accepted Answer

In the late game with massive maps, turn calculations slowed from 5 seconds to 15 seconds. It's a total mood killer for a strategy game. The default XMP profile on the MSI Z890 EDGE was hitting rare parity errors when handling huge amounts of unit logic, forcing the memory controller to constantly retry. I tried clearing temp caches, but it only saved me 1 second—I knew I needed a real fix. I went into BIOS and dropped the RAM frequency from 7200MHz down to 6000MHz, tuning timings to 30-34-34-80. Resource Monitor showed throughput stabilized at 52 - 56GB/s instead of erratic spikes, and turns started snapping back to normal. I didn't notice it immediately, but after three turns, the speedup was obvious. RAM temps are 45 - 51℃ at 1.35V. Four passes of MemTest86 showed zero errors. Hardware verified.

Question 10

I'm seeing frame drops during scene loads in Indiana Jones on my ASUS Z890-A Snow. Is this a bus synchronization issue?

Accepted Answer

The difference after this fix was insane. I was getting these 10 - 20ms micro-hitches while sprinting, which is a death sentence in an action-adventure game. The default bus frequency on the ASUS Z890-A Snow was causing micro-queuing delays with high-frequency RAM, making data throughput swing between 45 - 55GB/s. I tried 'Ultimate Performance' in Windows, but the P-Cores just ran hotter without fixing the stutters—software tweaks weren't enough. I rebooted into BIOS, locked the FCLK frequency at 2100MHz, and enabled the XMP profile. RivaTuner showed my minimums jumped from 40 to 72 FPS. It's finally silky smooth. It actually failed to boot at 2100MHz at first, until I bumped the SoC voltage to 1.2V. CPU temps are 62 - 68℃. Bus sync is confirmed, mode switched.

GamePP Frequently Asked Questions

Overview: GamePP real-time monitors in-game hardware performance issues. Playing game Fortnite with graphics card AMD Radeon RX 9070 XT, turned on overlay and FPS drops to 60, 1% Low FPS too low!

Overview: GamePP in-game monitoring for low-load FPS and temp display. Playing Counter-Strike 2 with my graphics card AMD Radeon RX 9070 XT, monitoring overlay drops 1% Low FPS to 80, ruining headshots!

Overview: GamePP troubleshooting optimization not taking effect for memory release In Monster Hunter Wilds with my memory Kingston FURY Beast 32GB DDR5 6000 at 90% usage, clicking Start Optimization still causes stuttering, 1% Low FPS only 45.

Overview: GamePP performance evaluation solves low GPU score issue In Black Myth Wukong with my Colorful iGame GeForce RTX 5070 Ti graphics card, the GPU performance score in GamePP computer benchmark is low, causing inaccurate frame rate prediction.

"Gamepp recording Naraka: Bladepoint—storage path full error, can't save clips?"