Question 1

Is adjusting memory mapping the answer when Control 2 crashes due to Fanxiang S910PRO 2TB?

Accepted Answer

I finally got to feel the raw speed of PCIe 5.0, and while the setup was a total pain, getting it to run smoothly was an absolute rush. The independent cache on the Fanxiang S910PRO 2TB is a beast, but during high-concurrency random writes, memory mapping conflicts caused data backups of 0.6-1.3GB, which just crashed the game. I tried dropping all textures to the absolute minimum, but the game looked like a pixelated mess and still crashed during map loads—the frustration was real. I eventually hunted down the '4G Decoding' option in the BIOS, toggled it on, and manually capped the shared cache threshold to under 1.8GB to force the system to use physical cache. My performance analyzer showed memory swap frequency dropping from 130 times/sec to 40-55 times/sec, and the game barely holds 50 FPS. I also lost access to some SATA drives after enabling 4G Decoding, which was a nightmare until I updated the BIOS. Drive temps are sitting between 55-68℃, and the heatsink is definitely warm to the touch.

Question 2

I'm getting sync errors and frame drops during heavy combat in God of War Ragnarok with Asgard Thor DDR5. Why?

Accepted Answer

I can finally face the Nine Realms without the game choking. The sync settings were a pain, but the optimization actually saved my frame rate, which feels amazing. The Asgard Thor DDR5 6400 was struggling in Gear 1 mode with XMP enabled, forcing the system to run constant error corrections in the background. This caused frame times to jump wildly between 14-35ms. I tried updating every single driver in Windows first, but it only gave me a pathetic 2 FPS boost—totally unacceptable. I went into the BIOS, forced Gear 2, and nudged the VDDQ voltage from 1.25V to 1.35V. RTSS showed the frame time curve instantly collapsing into a stable 11-15ms range, and the drops vanished. To be fair, switching to Gear 2 initially cost me about 5GB/s in bandwidth, so I manually overclocked the frequency to 6600MHz to make up for it. Temps sat between 52-60℃ with almost zero voltage ripple. MemTest86 confirmed the sync mode switch was successful, and temps stayed locked at 52-60℃.

Question 3

I'm hitting a bandwidth wall in sandstorm scenes with my Kingbank 8GB RAM. Should I be tweaking my memory timings?

Accepted Answer

I finally got this thing running; even with just 8GB, I managed to hold 40 FPS through some extreme tweaking, which feels like a win. The Kingbank Yin Jue 8GB DDR4 3600 in single-channel mode was hitting a wall during heavy particle effects, with latency spikes of 1.8-3.1ms that left the CPU just idling. I first tried cranking the virtual memory up to 24GB, but that actually made loading times 3 seconds slower, which was a total fail. I went back into the BIOS, switched timings from Auto to Manual, and dropped tRCD and tRP by 2 counts, while enabling memory compression in Windows. The performance analyzer showed latency dropping from 82ns to a range of 70-76ns, and the sandstorm lag completely vanished. I did hit a blue screen right after the first timing drop, but bumping the voltage from 1.35V to 1.38V stabilized everything. Memory temps sat between 42-50℃ and the clock stayed rock solid at 3600MHz. The mode switch is successful, and temps are holding at 42-50℃.

Question 4

Granblue Fantasy: Relink hitches during scene swaps on my ASRock H310CM-ITX; should I optimize the memory timings?

Accepted Answer

I finally got this running smoothly. It's an old board, but pushing the limits to get the frames back was a huge rush. The memory bandwidth on the ASRock H310CM-ITX/ac is way too low for modern 3A asset decompression, causing 1.5-2.8ms delays in memory page allocation. I tried cranking the virtual memory to 32GB, but that actually made loading 2 seconds slower—totally useless. I went into the BIOS, switched from Auto to Manual, and dropped tRCD and tRP by 2 units, then enabled memory compression in Windows. My analyzer showed latency dropping from 85ns to a stable 72-78ns, and the scene-swap stutters completely vanished. I did get a couple of BSODs at first, but bumping the voltage from 1.2V to 1.25V stabilized everything. Memory temps are 40-46℃ at 2666MHz. Frametimes are now a consistent 12-16ms.

Question 5

I'm seeing weird screen tearing in Zenless Zone Zero after enabling FSR frame gen, please help!

Accepted Answer

Hitting 120 FPS is an amazing feeling, even if they are generated frames, but the visual glitches were killing me. On the Sapphire RX 7650 GRE, FSR 3 was causing 2-5 pixel tearing artifacts during fast action because the sampling rate wasn't syncing with the refresh rate, and input lag felt sluggish at 25-35ms. I first tried disabling all driver enhancements, but my FPS plummeted back to 60 and the tearing stayed—totally unacceptable. I updated to the latest Adrenalin drivers, switched the FSR sampling mode from 'Quality' to 'Balanced', and turned on Anti-Lag. Using a frame comparison tool, I saw the effective frame generation time drop from 16ms to 8-11ms, and those edge artifacts finally vanished. I had some minor flickering after enabling Anti-Lag, but adjusting the monitor response time to 'Fast' fixed it. GPU temp is stable at 60-66℃ with power draw around 140W.

Question 6

I'm getting frame drops in Elden Ring: Shadow of the Erdtree because my Cooler Master B240 isn't cooling enough. Should I tune the rad fans?

Accepted Answer

I can finally face the final boss without my PC melting, though this AIO is getting old. I managed to squeeze every bit of performance out of it, which was a huge relief. The B240 was showing a 10-15℃ thermal drift under load, with cores idling in the 88-94℃ range, causing my FPS to swing wildly between 60 and 45. I tried forcing the pump to full speed via software, but the high-pitched whine was so piercing I couldn't hear the game—completely unacceptable. I ended up stripping the block, applying high-conductivity thermal paste, and switching to an aggressive fan curve based on CPU package temp in the BIOS. HWiNFO showed the load temps plummet from 92℃ to 76-80℃, and the FPS fluctuations totally stopped. The fans were a bit too loud at idle initially, but dropping the low-load RPM to 600 RPM made it perfect. Now it stays between 65-72℃. Benchmarks confirm the cooling mode switch worked, though I suspect the pump is nearing the end of its life.

Question 7

I'm getting major I/O blocking and frame drops in Manor Lords during city expansion on my Great Wall GW3300 512GB. Do I need to change disk priority?

Accepted Answer

I finally got it running! Even with only 512GB, some extreme optimization made it playable, which is actually a rush. The GW3300 512GB is just too small for massive city simulations; the system kept hitting a 0.8-1.5GB virtual memory deficit, causing the game to hard lock. I first tried tanking every single graphics setting to the absolute minimum, but the game looked like a mosaic and still crashed during saves, which was an incredibly frustrating experience. I then manually locked the page file to 16GB and tweaked the disk I/O priority weights in the registry. I saw the memory swap frequency drop from 110 times/sec to about 35-50 times/sec, and I can finally maintain 45 FPS. My boot time slowed down by about 2 seconds after the I/O tweak, but disabling 'Fast Startup' fixed that. Drive temps are 40-52℃, and the speed is steady at 3300MB/s. Frame gen is now stable at 5.1-6.4ms, though the drive is still a bottleneck.

Question 8

My Samsung 9100 PRO PCIe 5.0 triggers thermal throttling after long sessions of The First Descendant, causing FPS drops. Should I change the cooling strategy?

Accepted Answer

I finally got to experience PCIe 5.0 speeds, but the heat is insane—it's like having a small space heater sitting on my motherboard. The Samsung 9100 PRO core temps shot up to 82-88℃ under load, triggering the motherboard's thermal throttling and crashing my random read speeds from 12000MB/s down to 3000MB/s. Consequently, my FPS tanked from 110 down to 45. I first tried capping the PCIe link to 4.0 in the BIOS; temps dropped to 60℃, but loading times nearly doubled, which was a totally unacceptable trade-off. I ended up reinstalling the stock heatsink and adding a 40mm micro-fan blowing directly on it, while setting the M.2 fan curve to 'Aggressive' in the BIOS. HWInfo shows the drive now peaks at 62-68℃, and the speeds are rock steady. I had some annoying resonance noise right after installing the fan, but replacing the rubber pads solved it. Idle temps are now 38-42℃, and the benchmark curves are back to peak performance.

Question 9

Monster Hunter Wilds keeps crashing in complex areas because my ADATA 4GB DDR4 is insufficient.

Accepted Answer

I actually got it to run! Using only 4GB of RAM is basically a suicide mission for modern AAA titles, but the extreme optimization worked. The ADATA ValueRAM 4GB 2666 was constantly hitting a 0.5-1.2GB deficit when allocating shared VRAM, leading to immediate crashes. I first tried lowering all textures to the absolute minimum, but the game looked like a mosaic and still crashed during map loads—it was a total failure. I then went into the BIOS, enabled 4G Decoding, and manually capped the shared memory threshold at 1.5GB to force the system to prioritize physical VRAM. In the performance analyzer, memory swap frequency dropped from 120 times/sec to 30-45 times/sec, and the game barely holds 30 FPS. I had a problem where my SATA drives weren't recognized after enabling 4G decoding, but a BIOS update fixed that. Memory temps were 40-46℃ at 2666MHz. Resource monitoring confirms the shared mode switch worked, and fans stayed at 1400-1600RPM.

Question 10

Is my DeepCool AK500 suffering from heat soak during massive battles in Horizon Online? Should I increase intake?

Accepted Answer

I can finally explore the online world without it turning into a slideshow. It's a struggle for air cooling, but pushing the optimization to the limit actually worked, which is a huge relief. The DeepCool AK500 ARGB was struggling with heat accumulation at the base during high-power loads, causing CPU temps to bounce between 85-92℃ and triggering mild throttling. I first tried 'Ultimate Performance' mode in Windows, but it only gave me a 2 FPS boost—totally useless. I went into the BIOS, cranked the fan speed ceiling to 100%, and slapped two high-pressure fans in the front of the case to force more cold air in. RTSS showed the frame times tightening from a shaky 18-35ms to a consistent 14-17ms. I did have a bit of case resonance after adding the fans, but switching to rubber anti-vibration mounts killed the noise. CPU temps are now stable between 78-83℃. Stress tests confirm the cooling mode switch worked, and the system is no longer throttling.

GamePP Frequently Asked Questions

How to enable AI filter in GamePP for the game Palworld to improve GPU Gigabyte Aorus GeForce RTX 4090 Master 24G image sharpness?

How to use AI filters in GamePP to optimize the color contrast of GPU ASUS ROG STRIX GeForce RTX 5090 OC 24GB during gameplay in Dota 2?

How to apply game filters in GamePP to enhance dark area details for GPU ASUS ROG STRIX RTX 5090 in Naraka: Bladepoint?

During Black Myth: Wukong gameplay there are many noise points reducing immersion, how to use AI filter in GamePP to reduce noise?

In Overwatch, how to adjust color saturation with GamePP's game filters to fix dull image colors?